Microstructure,mechanical, tribological,and oxidizing properties of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings with different modulated thicknesses

Multilayer structure design is one of the most promising methods for improving the comprehensive performance of AlCrN-based hard coatings applied to cutting tools. In this study, four types of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings, with different modulated thicknesses, were deposited to investigate their microstructure, mechanical, tribological, and oxidizing properties. All multilayer coatings exhibited grain growth along the crystallographic plane of (200) with a NaCl-type face-centered cubic (FCC) structure. The results show that, as the modulation thickness decreases from ～35 nm to ～10 nm, (1) the grain refinement effect is increasingly evident; (2) all multilayer coatings show a hardness of >30 GPa and an elastic modulus of >300 GPa. Both the ability to resist elastic strain to failure and the plastic deformation of multilayer coatings increase. In addition, their resistance to cracking reduces; (3) the wear rates of these multilayer coatings reduce successively from 1.78 × 10^?16 m³ N^?1 m^?1 to 7.7 × 10^?17 m³ N^?1 m^?1. This is attributed to an increase in self-lubricating VO_x and a decrease in adhesives from the counterparts; (4) the best high-temperature oxidation resistance was obtained for the multilayer coating with a modulated thickness of ～15 nm.     

A comparative study of NdY-Fe-B magnet and NdCe-Fe-B magnet

Low cost and high abundance rare earth elements Y and Ce have attracted tremendous interests of the industrial and scientific societies for fabricating the highly cost-performance efficient rare earth permanent magnets. However, the effect of separate replacement of Nd by Y or Ce on the performances of NdFeB-type magnet under the same atomic ratio and preparation conditions is still unclear. In this work, we systematically investigated the magnetic properties, thermal stabilities and service performances of (Nd_0.8Y_0.2)_13.80Fe_balAl_0.24Cu_0.1B_6.04 (atomic fraction, denoted as 20Y) and (Nd_0.8Ce_0.2)_13.80Fe_balAl_0.24Cu_0.1B_6.04 (atomic fraction, denoted as 20Ce) magnets. The results demonstrate that the μ₀M_r, μ₀H_c and (BH)_max of 20Y magnet are respectively 1.325 T, 1.173 T and 343.467 kJ/m³, which are comprehensively higher than those of 20Ce magnet (μ₀M_r = 1.310 T, μ₀H_c = 0.948 T, (BH)_max = 321.105 kJ/m³). Moreover, the 20Y magnet has higher thermal stability compared with 20Ce magnet which is favorable for the magnetic performances at elevated temperatures. The investigation of microstructure and elemental distribution indicates that the excellent magnetic performances of NdY-Fe-B magnet can be attributed not only to the preferable intrinsic properties 4πM_s, H_a and T_c of Y₂Fe₁₄B, but also to the in-situ core–shell structure of the 2:14:1 matrix phase grain with Y-rich core and Nd-rich shell, along with the thicker grain boundary layer between the adjacent matrix phase grains in NdY-Fe-B magnet. Furthermore, the 20Y magnet exhibits better mechanical property and higher corrosion resistance than 20Ce magnet, which are helpful for prolonging the service life of the magnet in practical application.     

Sn-containing Si3N4-based composites for adaptive excellent friction and wear in a wide temperature range

Ceramic design based on reducing friction and wear-related failures in moving mechanical systems has gained tremendous attention due to increased demands for durability, reliability and energy conservation. However, only few materials can meet these requirements at high temperatures. Here, we designed and prepared a Sn-containing Si₃N₄-based composite, which displayed excellent tribological properties at high temperatures. The results showed that the friction coefficient and wear rate of the composites were reduced to 0.27 and 4.88 × 10^?6 mm³ N^?1 m^?1 in air at 800 °C. The wear mechanism of the sliding pairs at different temperatures was revealed via detailed analyses of the worn surfaces. In addition, the tribo-driven graphitization was detected on the wear surfaces and in the wear debris, and the carbon phase was identified by SEM, TEM, and Raman spectrum.     

Compatible performance of low thermal conductivity and high infrared radiation of Sm2O3-HfO2 series ceramics applied for thermal protection coatings

Sm₂O₃-HfO₂ series ceramics were synthesized at high temperature using the solid-state reaction. The phase stability, thermo-physical and infrared emission properties of Sm₂Hf₂O₇ (SHO) and Sm₂Hf₂O₇-44.83 wt%HfO₂ (25S/H) composite ceramics were comparatively investigated. Furthermore, their calcium magnesium aluminosilicate (CMAS) corrosion was conducted at 1250°C for different times. The results reveal that both SHO and 25S/H ceramics have excellent phase stability at 1600°C as well as excellent sintering resistance. SHO still exhibits slightly lower thermal conductivity and lower hardness and Young's modulus, higher thermal expansion coefficient (CTE) and fracture toughness as well as higher infrared emittance (0.899 at 800°C) than 25S/H composite with the excessive HfO₂ inside. Both SHO and 25S/H ceramics react with CMAS to form a relatively compact reaction layer, which can effectively prevent the penetration of CMAS. These results preliminarily indicate that SHO ceramic can be proposed as an alternative material of the traditional YSZ for high-temperature thermal protective applications thanks to its compatible performance of low thermal conductivity and high infrared radiation, etc.     

Thermal shock effects on the impact resistance,tolerance and flexural strength of alumina based oxide/oxide ceramic matrix composites

In this study the effects of thermal shock on the impact damage resistance, damage tolerance and flexural strength of Nextel 610/alumina silicate ceramic matrix composites were experimentally evaluated. Composite laminates with balanced and symmetric layup were gradually heated to 1200°C in an air-based furnace and held for at least 30 min before being removed and immersed in water at room temperature. The laminates were then subjected to low velocity impacts via a hemispherical steel impactor. The resultant damage was characterized non-destructively, following which the laminates were subjected to compression tests. Three-point bend tests were also performed to evaluate the effect of thermal shock on the flexural strength and related failure modes of the laminates. Thermally shocked laminates showed smaller internal damage and larger external damage areas in comparison to their pristine counterparts. For the impact energy and resultant damage size considered, the residual compressive strengths for the thermally shocked and pristine laminates were similar.     

Effect of nickel addition on the physicochemical properties of SrTiO3-based materials

Synthesis of materials in Ni/SrTiO₃ system was undertaken. Perovskite structure material with nominal composition SrTi_0.98O₃ was synthesised by the sol-gel method. Nickel was introduced into the system by the wet impregnation method followed by proper thermal treatment. Two research paths were carried out: the evaluation of sintering conditions on material properties (sintering temperature: 1100, 1200, 1300 and 1400 °C; sintering time: 1, 3 and 5 h for sintering at 1300 °C) and the effect of nickel addition on the material properties - 1, 2, and 5 mol% of Ni compared to the amount of Ti was introduced into the analysed system. The microstructures of the materials, together with their structural (XRD analysis) and electrical (total conductivity and Seebeck coefficient) properties, were determined. Furthermore, temperature-programmed reduction (TPR) and temperature-programmed oxidation (TPOx) measurements were performed to evaluate the materials’ redox properties. It was shown that less than 1 mol% of Ni could be incorporated into the strontium titanate structure when a wet impregnation was chosen as the method for the introduction of Ni into the SrTiO₃-based system. NiO and, for the highest amount of introduced nickel, also NiTiO₃ were the main additional nickel-containing phases. For all materials synthesised in the Ni/SrTiO₃ system, the positive value of the Seebeck coefficient was observed, suggesting that nickel is an acceptor-type dopant while incorporated into the perovskite structure. However, the TPR measurements clearly imply that nickel can be incorporated into the strontium titanate structure in various oxidation states.     

Concentration dependence of physical properties of low temperature processed ZnO quantum dots thin films on polyethylene terephthalate as potential electron transport material for perovskite solar cell

Colloidal Zinc oxide quantum dots (ZnO QDs) prepared with varying concentrations through precipitation method were deposited on flexible ITO/PET substrates using spin-coating technique. Various characterization tools were utilized to investigate the morphological, structural, electrical and optical properties of the films. The crystallinity of the films was found to improve with increasing ZnO QD concentration (ZQ_C) as evident from the X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) studies. Crystallographic and optical parameters were evaluated and explained in depth. The average nanograin size and bandgap were increased and decreased respectively, from ～5 nm to ～8 nm and 3.29 eV–3.24 eV with an increase in ZQ_C from 10 mg/mL to 70 mg/mL. Columnar structure growth of the films is revealed by AFM results. The films showed decent optical transparency up to 81%. All the ZnO films exhibited n-type semiconducting property as indicated by the electrical measurements with carrier mobility and low resistivity of 12.21–26.63 cm²/Vs and 11.84 × 10^?3 to 13.16 × 10^?3 Ω cm respectively. Based on the experimental findings, ZnO QD nanostructure film grown at 50 mg/mL is envisaged to be a potential candidate for flexible perovskite photovoltaic application.     

Centrifugally spun carbon fibers prepared from aqueous poly(vinylpyrrolidone) solutions as binder-free anodes in lithium-ion batteries

Aqueous solutions of poly(vinylpyrrolidone) (PVP) of various concentrations (20, 25, and 28 wt%) were successfully spun into fibers by centrifugal spinning. The pristine PVP fibers were annealed and carbonized to produce flexible carbon fibers for use as binder-free anodes in lithium-ion batteries. These flexible carbon fibers were prepared by developing a novel three-step heat treatment to reduce the residual stresses in the pristine PVP precursor fibers, and to prevent fiber degradation during carbonization. The thermogravimetric analysis data showed that the annealed fibers yielded a residual mass percentage of 36.0% while the pristine PVP fibers suffered a higher mass loss and only retained 26.5% of original mass above 450 °C (under nitrogen). The electrochemical performance of the carbon-fiber anodes was evaluated by conducting galvanostatic charge/discharge, rate performance, and cycle voltammetry experiments. The 20, 25, and 28 wt% derived binder-free anodes delivered specific charge capacities of 205, 189, and 275 mAh g⁻¹, respectively, after the first cycle at a current density of 100 mA g⁻¹. The results obtained in this work indicate that a feasible pathway towards a large-scale production of carbon-fiber anodes from a 100% aqueous solution can be achieved via centrifugal spinning and subsequent heat treatment.     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.